2012 to 2015 Jeep Wrangler V6 Models Gain More Horsepower with K&N Performance Air Intake System

Feb 19, 2013

Air Intake for 2012 to 2015 Jeep Wrangler 3.6L

Jeep Wranglers are notorious for being the ultimate off-road vehicle. They are used by park rangers, fire departments, police, and the U.S. military. These authority figures probably choose this vehicle because of its ability to maneuver through rough terrain, and stay on all fours while doing so. Whether you are on the trails, driving around the beach, or cruising on the highway, Jeep Wrangler models have proven adaptive in all types of conditions. No doubt the suspension, chassis, and body of the 2013 Wrangler is quite impressive and when combined with the 3.6 liter V6 engine, it is bound to turn heads.

When your destination is uncertain or if you are just out to have some fun, extra horsepower is not a bad idea. K&N's 77-1566KP air intake system is guaranteed to increase horsepower and torque in your 2012 to 2015 Jeep Wrangler with the 3.6 liter engine.

77-1566KP installed on a 2012 Jeep Wrangler 3.6L

This performance air intake is a free-flowing mandrel-bent aluminum tube induction system, which is built to dramatically decrease intake restriction as it smoothens and straightens air flow. This allows the Wrangler's engine to breathe easier than the OEM air box assembly. More air means extra usable power and acceleration throughout the engine's RPM range.

The cone-shaped air filter (RF-1048) included in the kit is washable and reusable, which means money will be saved in the long run by eliminating the need to purchase a new disposable replacement OEM filter every few-thousand miles. The driver also avoids the need to throw away the dirty filters every time it's changed. This helps reduce unnecessary waste in our landfills, while supporting a healthy environment. K&N air intake air filters can be used for up to 100,000 miles between cleanings, depending on driving conditions.

Dyno results for a 2012 Jeep Wrangler with 77-1566KP installed

K&N air intake 77-1566KP is equipped with a heat shield that helps deflect heat from the engine especially during idle. This helps cooler air get to the motor and it can result in better performance. This K&N air intake system uses a chrome like finished aluminum tube that is machined specifically for the 3.6 liter Jeep Wrangler. With an estimated gain of 10.2 Horsepower at 5600 RPM and 8.6 ft/lb of torque at 4188 RPM, this air intake can be a vital improvement for any off-road enthusiast. But don't think the extra horsepower you gain is exclusively for the off-roader; a K&N air intake can prove beneficial to any vehicle and provide additional performance when you need it.

Installation is easy with common hand tools, since 77-1566KP contains step-by-step instructions that include photos to make adding performance simple. Last, but certainly not least, 77-1566KP comes backed by K&N's Million Mile Limited Warranty.

K&N 77-1566KP will fit the following Jeep Wrangler models:

2015 Jeep Wrangler 3.6L V6
2014 Jeep Wrangler 3.6L V6
2013 Jeep Wrangler 3.6L V6
2012 Jeep Wrangler 3.6L V6

For a full list of K&N air intake systems for Jeep Wrangler models, visit the Jeep Wrangler Air Intakes page on KNFilters.com.

Be sure to check out some of these cool SEMA Show Jeeps; Alex Andrade's 2012 SEMA Jeep, VWerks JK8 Hemi Conversion and Falken's 2009 Jeep Unlimited

Find K&N products for your vehicle using the K&N application search then use the K&N dealer search to find a K&N dealer in your part of the world.

← PREVIOUS

K&N High-Flow Air Filter Assembly for USAC Ford Focus Midget Racing

International Trucks and Busses Get a Washable Reusable Heavy Duty Commercial Grade Air Filter