Últimas noticias

Milton Peters' Custom Chopper is a Celebration of Beauty, Speed, and Power

Custom chopper with 127ci motor and K&N filter

Milton Peters’ stunning Green Monster is protected by legendary K&N filtration

Milton Peters’ stunning chopper is named after the iconic left field wall in Fenway Park. The bike’s designer and builder says he has always been a “huge Boston Red Sox fan.” In reality, Peters’ “Green Monster” shares very little in common with its namesake other than color. Fenway’s version is tall, stationary, and silent. Peters’ version is low, fast, and anything but quiet.

Leaving well enough alone is not in Peters’ DNA. “I started building, modifying and ‘chopping’ anything with wheels as a kid and then into my teenage years,” he reflects. Even with the success of his Green Monster, Peters is quick to deflect the label bike builder. “I was never a bike ‘builder’ until this project. There are plenty of custom parts on the bike, but I am still more of a novice assembler and far from the talents of many amazing builders. The amount of respect I have for any builder / assembler or even the everyday repair gurus is very high.” While Peters’ humility is refreshing, the quality of the build and the incredible visual unity of the chopper speak to a deep-rooted talent.

Custom one off exhaust on chopper

Serious work went into these exhaust bends, and it was worth it

In reality, the lion’s share of Peters’ customization experience has come on four-wheeled vehicles. “I have built and customized import cars that were featured in international magazines and even built an Isuzu Pup mini truck and fabricated my own body drop and installed my own hydraulics despite never have used a torch or welder before, and created a full custom stereo. I have been more heavily involved in the aftermarket automotive, recreational vehicle, and electronics scene for about 20 years now.”

According to Peters, the Green Monster is a product of about 15 years of thought, planning, and mental incubation. All of that rumination is evident in the overall aesthetic unity of the creation. Let’s start with the paint. As for all those green bits on the chopper, Peters says, “I wanted the paint to be candy for sure. I wanted the paint to scream ‘extreme’ yet not be too busy.” The color is not the end of the visual feast as Peters thinks his paint details make the difference. “I feel that this custom candy green paint, the skull on the tank, the flames and then all of the small elements that match throughout the entire bike, are what makes this bike different.”

K&N filter inside S&S intake housing

The K&N filter inside that intake helps those big jugs pump out serious horsepower

Peters knows that a great chopper is not just about paint, despite the societal influence of what he calls “the commercialized chopper scene.” While that fad has faded, Peters is quick to point out that chopper building is alive and well. He says, “There are still plenty of shops, plenty of garage projects, or even people like myself who just finally said, ‘I am going to do this and I am doing it because I want to.’” The details of the Green Monster go much deeper than that paint.

The bike’s exhaust is a primary styling, performance, and auditory element. Getting the pipes just as Peters wanted them took some work. “I wanted the old school, heat wrapped look while having a slight ‘up sweep’ to it and of course an aggressive idle and rumble. I took a new exhaust and heated the bends. First, I had to get the exhaust past the housing, and I also wanted to sweep it up and out more. Next, I heated both pipe ends and brought them together slowly. I made a new bracket to mount them together and it works out visually and sounds exactly how I want it to.”

Custom open primary with 3.5-inch belt

Attention to detail is everywhere on the Green Monster

Peters wanted other design details to “match and be stand out items, but be subtle.” Many of those details are machined to match the chopper’s distinctive rims. The brake rotors and drive pulley are cut to match the wheels. Proving no detail is too small, even the valve stems are machined to match. “The bike features a black frame with a good combination of chrome, black and aluminum throughout.” Peters continues, “The S&S intake with the K&N filter even has a chrome housing and I added in the black accent cover to the face of that. It is pretty clear that I wanted the bike to flow nicely. I feel the bike has a great balance of the three metals - chrome, black, and aluminum.”

So what about the engine in the beast? Well it’s impressive. The big twin pushes a displacement of 127 cubic inches. It has forged pistons and roller rockers. The power-plant produces approximately 160 horsepower and more than 150 foot-pounds of torque. It delivers that power to the road through a 6-speed, right-side drive and an open primary with a 3.5 inch belt drive.

Custom chopper with pearl green paint

The sexy lines of Milton Peters’ creation are the result of years of visualization

Peters trusts K&N to protect his fire-breathing labor of love. “I truly have used K&N for many years. My first oil filter and air intake were K&N back in 1997. I have trusted them ever since. The washable and re-usable part is nice but to me the performance and instant throttle response I feel from the K&N air filters and intake systems is worth it all. In my daily drivers and in my motorcycle, I know I can trust the all of the K&N filters to perform.” Of course, K&N has a full range of filters and intakes for your particular project. Use the online application tool to get what you need.

With the Green Monster complete, what’s next for Peters? “I have contemplated selling this chopper and building another; maybe a bagger. But then literally every time I look in my garage I smile. So I am often torn. That being said, I also think I may build something again with 4 wheels, maybe a hot rod, muscle car, or extreme 4X4. The jury is still out.” Whatever Peters decides to tackle next, rest assured that it will be unique, it will be fast, and it will be fitted with K&N products.

clear

K&N PRODUCT SEARCH     WHERE TO BUY K&N

clear

Gragson Sweeps NASCAR K&N Pro Series West Doubleheader Races at the Utah Motorsports Campus

Noah Gragson leading at Utah Motorsports Campus

Noah Gragson in the No. 7 car leads the field in the NASCAR K&N Pro Series West race at the Utah Motorsports Campus

Noah Gragson swept the K&N Pro Series West doubleheader at the Utah Motorsports Campus and returned to victory circle for the first time since June.

“It feels good to sweep the weekend,” Gragson said. “This is what we needed. Heading off to the next race, we got a road course in the East Series. I’m just really pumped up right now.”

Gragson, one of the NASCAR Next drivers, won the first race after leading the last 10 laps of the Utah 110 presented by Ken Garff Volvo. He won the second race taking the lead on the last lap of the race.

“This is pure, never give up attitude,” Gragson said. “We really need this as a team. I am just so pumped up for all my guys, they worked real hard for this.”

Noah Gragson, Todd Gilliland, and Ryan Partridge on the podium

Noah Gragson, center, won the second of two NASCAR K&N Pro Series West races at the Utah Motorsports Campus. Todd Gilliland, left, was second, and Ryan Partridge was third

In the first race, Ryan Partridge won the pole and led the first 22 laps of the K&N Pro Series West race. Rookie Todd Gilliland, the leader in the K&N Pro Series West standings, passed Partridge on lap 23 and was out front for three laps.

Gracin Raz was third, followed by Julia Landauer in fourth and Riley Herbst in fifth.

Gragson took the lead from Gilliland on lap 27 and won the race by 1.086 seconds. It was Gragson’s fourth win of his K&N Pro Series career. He won the K&N Pro Series East race at Stafford Motor Speedway in Connecticut in June.

Noah Gragson on the podium at Utah Motorsposrts Campus

Noah Gragson swept the weekend doubleheader of NASCAR K&N Pro Series West races at the Utah Motorsports Campus

“Made my way into second chasing the 16 car (Gilliland),” Gragson said. “He made a mistake down in turn 1 with probably 11 or 10 to go. I took away the lead and I think that was the game-changer in the race. That’s what changed everything. Got some momentum on our side just being the leader. He really burned his stuff up there trying to run me down. He’d get close and then blow the corner, get close again and blow the corner.”

Gilliland said his inexperience on road courses mixed with his aggressive strategy to catch Gragson cost him in the race.

“It’s my first road course. It’s no excuse,” Gilliland said. “I kind of overdrove it, kind of got off track. I let the 7 (Gragson) pass me. I got back to him and I overdrove it again and let him get away.”

Noah Gragson in victory lane at Utah Motorsposrts Campus

Noah Gragson won the NASCAR K&N Pro Series West at the Utah Motorsports Campus. It was the fifth K&N Pro Series win of his career. He won the K&N Pro Series East race at Stafford Motor Speedway in Connecticut in June

In the second race in Utah, Partridge won the pole again, his fourth of the season. This time he was out front for five laps before Gilliland, who started on the front row, passed him. Gilliland and Herbst battled for the lead over the next 30 laps before Gragson passed both of them on the final lap.

“I just ran my race. Stayed focused, stayed positive,” Gragson said. “That’s really all I could do. Had a really good car, just one race on those tires. I’m really pumped up for my team, two in a row this weekend.”

Gragson won the second race with a 3.809-second margin of victory over Gilliland. Partridge was third, followed by Herbst in fourth and Todd Souza in fifth.

Ryan Partridge won the pole at Utah Motorsports Campus

Ryan Partridge won the pole for both NASCAR K&N Pro Series West races at the Utah Motorsports Campus

“I thought I put my team back in a hole, messed up on a restart about halfway through running fifth,” Gragson said. “I was feeling down, but my crew chief told me that we were still in this thing, just really happy for these guys. Made my way back up and kept fighting till the end.”

Gilliland has a 13-point lead over Partridge in the K&N Pro Series West standings with two races to go. Gragson is 37 points behind Gilliland and in third place.

“It feels good,” Gragson said. “This is what we needed momentum wise. The guys worked really hard for it.”

The next K&N Pro Series West race is at Meridian Speedway in Idaho on Sept. 24.

clear

K&N PRODUCT SEARCH     WHERE TO BUY K&N

clear

K&N Driver's Mike Maier and Jake Rozelle Go Head-to-Head at Circuit of the Americas

Jake Rozelle and Mike Maier at Circuit of the Americas

K&N driver's Jake Rozelle with his 1969 Camaro and Mike Maier with his 1966 Mustang at famed venue Circuit of the Americas

Possibly the most fun we've had out on the track this season would be witnessing the friendly rivalry between the Optima Search for the Ultimate Street Car series GTV Class K&N sponsored drivers Mike Maier, in his 1966 Ford Mustang and Jake Rozelle, in his 1969 Chevrolet Camaro. What makes this so much fun is just how closely matched they are when it comes to talent and speed. And really, who doesn't like seeing a Ford and Chevy throw down?

Jake, a recent graduate from the University of California San Diego with a Bachelor's in Science and Engineering, is young, scrappy, and super talented behind the wheel of his 1969 Camaro built by JCG Restorations. As potentially the youngest competitor in the OSUSC series, there isn't much that can stop this talented K&N driver from grabbing a podium at an Optima Series event. Over the past few years we've watched Rozelle grow up before our very eyes. We've watched as he became a household name thanks to MAV TV and Optima Search for the Ultimate Street Car television series. He's beguiled us all with his charm and winning smile.

Jake Rozelle being interviewed for Mav TV

Jake enjoying the spoils of success while being interviewed for Optima's Search for the Ultimate Street Car by Lucas Oils MAV TV

The Maier name has long been associated with motorsports. Collectively, the Maier family has more than 46 years in racing. Mike has enjoyed a longstanding relationship with K&N. Whether as a competitor in USAC as a K&N team driver in the Ford Focus Midget Series or being a brand ambassador in SCCA as a national champion with numerous trophies to show for it Mike is definitely a guy who can wheel a car. Talented and earnest, he's been racing most of his life. But he's not just a driver. Mike is a family man and business owner. For the past two years, he and wife, Brianne, have spent almost every waking hour building and growing their new business, Mike Maier, Inc. So when he's not racing on the weekends, you'll find him at the shop designing, engineering, and fabricating suspension and chassis parts for his customers. Maier's specialty? Track tested, Maier approved, Mustang Performance Parts. Certainly no surprise there.

Jake Rozelle driving his 1969 Chevrolet Camaro at Circuit of the Americas

Attention to detail and focus creates a great driver. Rozelle exhibits both

If you've been to an Optima track event or even a Goodguys show you've seen both of these fellas hanging it all out for the win. While Mike is a more seasoned racer with 20 plus years of racing experience, Jake comes to the track with an indescribable intensity that comes from youth. We've all been there. That sense of invincibility and the idea that we can conquer anything life throws our way. A certain confidence that far too many of us outgrow. But don't count maturity and wisdom out just yet. Mike brings his years of racing experience to the track that ultimately translates into him being a worthy opponent.

The seventh installment of qualifying events for Optima Search for the Ultimate Street Car challenge, presented by Advance Auto Parts, made its way to Austin, Texas, to the famed F1 venue, Circuit of the Americas. Jake was primed and ready to go. This year he is gunning for number one spot as points champion for this Optima series and has now attended four of the series qualifying events. In fact, he has earned a first place finish at his first three events. Having father Roy, along with JJ Furillo of Ultimate Performance trackside, has made this adventure better in all ways, from improved car performance to great fatherly advice and coaching, Jake has really shined throughout the season.

Mike Maier driving his 1966 Ford Mustang at Circuit of the Americas

From chassis tuning to alignment adjustments, Maier would do anything he could to catch Rozelle in autocross

While this is only Mike's second Optima event this season, he has taken time to make major improvements and killer mods to Ole Blue that would ultimately benefit him at COTA. His latest suspension designs, along with widened stance, and fatter Falken tires, provided better grip on the track in the Texas heat. Maier went to Texas on a mission, to get the invite. The coveted invite to the Optima Series finale, OUSCI immediately following SEMA. The question on everyone's mind was could he do it?

Day 1 at COTA saw the largest field of drivers competing this season at any one event. The field would be split between the Detroit Speed & Engineering Autocross and Powerstop Brakes Speed Stop challenge. Jake and Mike started at autocross together. This allowed them the opportunity to keep tabs on each other's lap times, and made for some healthy competition. One pushing the other a little more, a little quicker. After the first few runs Mike felt a severe case of understeer in Ole Blue, so he and his team got to work tuning the chassis. However, tuning was cut short between runs by an odd brake pedal/master cylinder problem. Turned out that a problem with the balance bar and alignment caused one pushrod to bend, then during another run a second rod would bend. Fortunately, they got the issue fixed and before the session was over Mike would get his quickest lap time of 29.749. Jake, refusing to give any ground, would get his lap time down to 29.551 a crucial 2/10th's of a second faster, earning him a first place finish in the GTV Class at autocross, as they headed over to the Speed Stop Challenge.

Jake Rozelle driving his 1969 Chevy Camaro in autocross

Jake gave it everything he had in autocross and came in 1st in GTV Class with a lap time 2/10th's of a second ahead of Mike

At the Speed Stop challenge, these two racers threw down the gauntlet. Every run would see Mike and Jake swapping first and second position, back and forth. Jake was pushing his 1969 Camaro to the max with each run, but Mike had Ole Blue just where he needed her to be competitive. It was only a matter of time before the clock would run out and Maier would claim victory, by 2/100th's of a second! Talk about cutting it close!

The next component these gentlemen would compete in was the Lingenfelter Design & Engineering segment. Maier has struggled a bit in the past with his scores in D&E. Mike admittedly focuses on performance and function first over form. It appears though, the judges approved of his recent mods and upgrades to Ole Blue. Rozelle on the other hand has regularly been rewarded with high scores as his Camaro always seems to please the judges. As per usual, Jake received a high score of 96 points, in a tie for second place with Kevin Tully, who also received 96 points for his 1964 Plymouth Valiant. In an incredible three-way tie for third place, Mike Maier would receive 93 points in Design & Engineering for Ole Blue, alongside Craig Johnson with his 1963 Ford Falcon and Larry Woo in his 1968 Chevrolet Camaro. A definite first in the Optima series event.

Jake Rozelle driving his 1969 Camaro in te speed stop challenge

At the Speed Stop Challenge, Rozelle's runs were picture perfect getting him a little closer to the win with each lap

Saturday's fun concluded with the Lucas Oil Road Rally. After a scorching triple digit day, with humidity off the charts, the drivers were treated to a rather simple rally consisting of just 1 checkpoint at Advance Auto Parts in Austin, and a mere 24 mile round trip adventure. We are happy to report that each of the drivers made it safely back to the track with smiles on their faces.

Day 2 at COTA meant it was time for the Falken Tire Hot Lap Challenge on the infamous F1 Road Course. Drivers were scurrying to make last minute adjustments to their cars and installing their transponders. Road course would literally consume the whole day and there was no sign of relief from the heat. It would be imperative for these drivers to not only pay attention to their cars response to the triple digit heat, but to pay attention to their body's response to the heat, as well.

First order of business was the driver's meeting with the typical pre-track talk, where to pass, flags and what they mean, use the whole track, big speeds and by all means don't crash and burn! We spoke to Jimi Day, USCA Race Director, and he shared that this Optima series event was the very first of its kind here at COTA. During the driver's meeting he would emphasize safety and encouraged the drivers to make note of this unforgettable experience, because it's not every day you get to race your street car on an F1 course!

Mike Maier driving his 1966 Mustang in the speed stop challenge

Maier’s new, wider stance and lunch time spring and chassis adjustments brought the Speed Stop Challenge home for the win in GTV Class. Just 2/100th’s of a second faster than Rozelle

The drivers would be broken down into three groups: novice, intermediate and expert, with Jake and Mike being part of the expert run group. Each group would have four run sessions in which to lay down their fastest lap time of the day. They would take part in orientation laps to familiarize themselves with the road course, then the fun would begin! On Maier's first session out, about a half a lap in, Ole Blue lost a bolt out of the shift linkage leaving the car stuck in 4th gear. This left him three run sessions to work with in effort to catch Rozelle, who seemingly was problem free in his Camaro. Maier would start his second session at the back of the pack and have to work his way through traffic as a result of the first sessions mechanical issues.

We could see in the second expert run session, both of our K&N drivers were getting really comfortable with the track. In fact, for every improvement Mike made, Jake also improved, running smoother and faster with each lap. By the third run session the heat was beginning to take its toll on the other cars and drivers. We watched in horror as a late model Corvette caught fire in the paddock area. Fortunately, the hood was the only casualty. Before Maier headed out, he made a sway bar adjustment that proved to be the right move. He knew if he was going to beat Jake he would have to get after it. But Jake would not lay down and he made Mike work for every tenth of a second. In the final run session, Maier would make one last critical adjustment before heading out. And then it happened. He would drop another full second off his lap time, ending him at a lap time of 2.29.0 which was enough for him to leapfrog to first overall in GTV Class for the weekend.

Mike Maier driving on the hot lap challenge

Falken Tires Hot Lap Challenge saw some challenges throughout the day. But Mike Maier, brought ALL of his years track experience to the course and came out the victor in GTV Class, ultimately securing him the overall win by just one point

The question on everyone's mind, could Mike Maier take the overall win from Jake Rozelle? The answer? YES. Mike Maier, with all the challenges and mechanical issues he encountered, was able to come away the winner overall in the GTV Class securing him the invite to OUSCI. It didn't come easy though. Jake Rozelle is a force to be reckoned with and never backed down. Only one point separated first from second place in GTV Class and in the end these drivers put on one heck of a show.

Even with the incredible heat and humidity, plus the on-track and in-paddock mishaps that took place at COTA, all of the drivers said they'd come back to Austin, Texas, to once again run the Optima series at Circuit of the Americas. Each of them leaving with memories of a lifetime, regardless of where they finished. Congratulations to Mike Maier on his COTA win and to Jake Rozelle for his continued point lead in GTV Class. We'll see you two at NOLA for the 8th installment of the Optima series qualifying event and will be cheering you on.

For more information about this series, log onto www.driveusca.com. And to improve your car performance, use K&N's product search. These are the same products our drivers use to improve their car's performance.

clear

K&N PRODUCT SEARCH     WHERE TO BUY K&N

clear

More Horsepower and Torque for 2003-2008 Dodge Ram 1500 Thanks to a K&N Oil-Free Air Intake

K&N 71-1533 Blackhwak intake for 2003-2007 Dodge Rams

All Blackhawk Induction Air Intake Systems come fitted with an exclusive engraved plate

If you're an owner of a 2003 through 2008 Dodge Ram 1500 equipped with the 5.7-liter Hemi engine, you probably know well that your engine produces 345 horsepower. You probably also know that for 2009 the 5.7 L Hemi was upgraded to produce 390 horsepower, 45 more horses than your truck.

If you'd like to make up some of that horsepower, K&N has just what you're looking for. It's the K&N 71-1533 Blackhawk cold air intake system and it adds an estimated 9.62 rear wheel horsepower to your 2003 - 2008 5.7-liter Hemi-powered Dodge Ram 1500.

That's not to say that the first generation 5.7-liter Hemi isn't a remarkable engine. While not a "true" Hemi like its predecessors from the 1950s and 1960s, its combustion chamber is reminiscent of a Hemi-based NHRA Top Fuel cylinder head, both of which have twin spark plugs. The Chrysler engineers who developed the first of the new generation of Hemi engines even invited the input of the engineers who designed the 426ci "Elephant" Hemi engine in the 1960s.

Some features of the 5.7-liter Hemi, code named Eagle, are a deep-skirted cast iron block, four bolts per main bearing (two installed vertically, two horizontally). The cast eutectic slipper-style pistons are light, as are the connecting rods which don't require a balance pad. The cylinder heads are cast from aluminum, and the intake manifold is molded of high-strength plastic, for both weight reduction as well as a smoother surface for better airflow. All up, the 5.7-liter Hemi weighs 56 pounds less than the 5.9-liter engine it replaced.

While the original 5.7-liter Hemi is a great engine, you can make up some of the horsepower difference with 2009+ models by installing a K&N Blackhawk performance intake kit which adds horsepower and acceleration to your 5.7-liter Hemi, providing an increase of up to 50% incremental air flow to the engine.

K&N 71-1533 Blackhwak intake installed on 2007 Dodge Ram

The K&N 71-1533 Blackhawk Induction Air Intake System blends well under the hood of a RAM 1500

This is possible because the low restriction air intake allows your engine to breathe more deeply than it would from the OEM air intake. More air means more power and acceleration. This K&N Blackhawk Induction Air Intake System comes with black components including the K&N high-flow air filter and heat shield. An engraved K&N logo is welded to the attractive textured black powder-coated tube for a clean, high-performance look. The intake tube features fittings for the factory inlet air temperature sensor and crankcase vent hose.

Key to the performance increase is the oversized conical air filter manufactured from K&N's DryFlow oil-free non-woven synthetic media. This type of construction not only allows for increased air flow but also offers excellent filtration characteristics to ensure a long engine life. Each design is verified through K&N's in-house filtration testing lab, which adheres to ISO 5011 standards, ensuring that K&N filters provide high airflow without giving up engine protection.

Best of all, the K&N Blackhawk Induction Air Intake System can be installed in 90 minutes or less with simple hand tools. And once you've installed your K&N filter you've eliminated the need to buy another air filter for the life of your Dodge Ram 1500. The only maintenance is a service you can do yourself in no time at all. At intervals of 100,000 miles (depending upon your driving conditions) by using the K&N synthetic air filter cleaner K&N 99-0624 you can easily clean your Blackhawk air filter, preparing it for 100,000 more miles of driving. Your one K&N air filter is designed to last for the lifetime of your vehicle, which K&N guarantees will perform for up to 10 years or 1,000,000 miles without requiring replacement. For full details visit the K&N Million Mile Limited Warranty.

Visit the Dodge Ram 1500 Air Intakes page for all K&N intake systems designed for Ram 1500 models.

.

The 71-1533 fits the following vehicles: 2008 DODGE RAM 1500 PICKUP 5.7L V8
2007 DODGE RAM 1500 PICKUP 5.7L V8
2006 DODGE RAM 1500 PICKUP 5.7L V8
2005 DODGE RAM 1500 PICKUP 5.7L V8
2004 DODGE RAM 1500 PICKUP 5.7L V8
2003 DODGE RAM 1500 PICKUP 5.7L V8

Not legal for sale or use on any pollution controlled motor vehicle in California or states adopting California emission procedures. See knfilters.com for CARB status on each part for a specific vehicle.

clear

K&N PRODUCT SEARCH     WHERE TO BUY K&N

clear

Turbo or Not, K&N Helps Your 1.2L PureTech Engine Breathe More Efficiently

K&N 33-3039 replacement panel air filter for Citroen and Peugeot

K&N filters achieve high intake airflow without risking engine protection

The Peugeot 208 was, for at least a brief time, one of the most famous cars in the world. This particular car, while not actually a 208 but a dedicated race car, did carry a body very clearly based on the shape of the 208. Named the 208 T16 and weighing just 1,929 lbs., it was powered by a 3.2-liter, twin-turbo V6 engine that produced 875 horsepower. And the purpose of this fiendish creation? To give Sébastien Loeb a hammer to smash the existing record at the 2013 Pikes Peak Hill Climb, the first year the event was run on fully paved roads. Rhys Millen's existing record of 9:46.164 was shattered by Loeb with a blindingly fast run of 8:13.878.

Now while you may not take a stab at Pikes Peak or even Mont Ventoux, your Peugeot 208 1.2-liter deserves some extra power. And it couldn't be easier - remove your old, inefficient air filter, open the K&N box containing part number 33-3039 and slide the new high-efficiency air filter in place - which has been designed to boost horsepower and rate of acceleration.

And it's not just the Peugeot 208 that the K&N 33-3039 fits but a whole range of French vehicles from 2013 to 2015 that share the same 1.2-liter three-cylinder engine: Peugeot 308 five-door hatchback, 2008 small SUV, and 5008 compact crossover, along with the Citroen DS3 super mini, DS4 five-door hatch, Picasso MPV, and Cactus, the quirky crossover.

The 1.2-liter engine has been named the PureTech by Peugeot and includes a number of interesting design features. The company determined that a three cylinder could be more efficient than a small four cylinder engine, through weight reduction, friction reduction, and a reduction of components and complexity. The base 1.2-iter EFI produces 82 horsepower, while two versions of the turbocharged PureTech generate 110 horsepower and 130 horsepower, respectively. And no matter if your 1.2-liter PureTech is turbocharged or not, it can benefit from the same K&N 33-3039 high-efficiency air filter.

K&N 33-3039 replacement panel air filter for Citroen and Peugeot with box

Everything you need to add more power and performance to your PureTech 1.2 L comes in the box. All you need are basic hand tools and around 5 minutes.

The increased airflow of a K&N air filter is achieved through the utilization of multiple layers of oiled cotton filter media, which offers less restriction than traditional filters. The multi-layered cotton filter material also filters out microparticles that could damage your engine. To make certain that each filter design provides high intake airflow without sacrificing engine protection, testing is conducted in K&N's own internal laboratory, which adheres to strict ISO 5011 protocols.

Once the K&N 33-3039 air filter has been installed you've eliminated the need to purchase and replace traditional filters for the life of your PureTech 1.2-liter Peugeot or Citroen. The only maintenance required you can do yourself in just a short time. At intervals of 50,000 miles or about 80,000 kilometers (depending on your driving conditions) clean and re-oil your air filter with a 99-5000 K&N air filter cleaning kit, returning it to like-new condition. Your one K&N air filter is designed to last for the lifetime of your vehicle, which K&N guarantees will perform for up to 10 years or 1,000,000 miles without requiring replacement. For full details visit the K&N Million Mile Limited Warranty.

To find additional K&N upgrades for cars, trucks, scooters, motorcycles, motorhomes, or almost anything with an engine, use the K&N search by vehicle tool. Find an authorized K&N dealer nearby using the K&N dealer search.

clear

K&N PRODUCT SEARCH     WHERE TO BUY K&N

clear